US Grout is actually an upgraded version of the caulking agent. When it is applied to tiles and floor tiles, it will be used as a decoration material with outstanding decorativeness and practicality, because US Grout will raise the floor tiles and tiles. The integrity and perfection of the effect are presented, so it is also loved by the consumers. So, the shortcomings of US grout are gone? In fact, the advantages of the US sizing agent are as prominent as those of the US sizing agent. The following Xiaobian will tell you where the shortcomings of the US sizing agent are, and how the US sizing agent is used correctly. 
What are the shortcomings of the US grout ?
Disadvantages of the United States and the first agent , construction defects: When the construction is completed, we must check it, this time is to find there will be some uneven places, especially where the vertical and horizontal intersection, using this is also very difficult to achieve smooth.
Disadvantages of the US sizing agent Second , the appearance of defects: the disadvantages of the US sizing agent compared to its wear resistance is relatively poor, and it is easy to filth. Especially for microcrystalline stone, fine polished glazed bricks, vitrified tiles, and its concave surface, this is also very small gaps that cannot be bonded at all.
Disadvantages of the US sizing agent Third , performance defects: This product has insufficient adhesion, the tile is not very smooth, then in the four seasons, the gap between the US sizing agent and the tile is very easy to crack, peeling and falling off. US grout is not resistant to water, aging quickly.
US grout usage method and dosage explanation
1, first to clean up the brick seam, you can use the utility knife to deduct the debris in the gap, when used must be dry, no dust phenomenon.
2. Remember to use a brush to clean the magazine in the crevice. Then use a clean wet towel to wipe the tiles hard. In this way, you can thoroughly clean the debris and dust.
3. When refilling, be sure to affix neatly embossed paper to both sides of the tile. Then just leave the construction site.
4, with a glue gun evenly hit the inside of the gap, this side to remind about the force must be maintained evenly. Need to be able to work several times.
5, you can use a small scraper to scrape the excess material so that the effect is more smooth, which will reduce the shortcomings of the United States and the United States in the first case.
6, we must remember to use a wet sponge to clean the overflow of the United States and so do.
7. Next, open the textured paper, remembering to leave textured paper on the tiles for a long time, which will also affect the construction results.
8, after the construction is completed, if you are in the summer it is about to open it for about two to three hours. The specific time will be determined according to the actual situation. It can be cleaned normally after about 12 hours.
9, high-quality construction process can reduce the appearance of the United States and the shortcomings of the joint, so the construction of the personnel and technology have more stringent requirements.
Summary: What are the shortcomings of the US Grout? How to use the US Grout and how to use it. Explain the relevant content and introduce it to this. We know that no matter what product it is good or bad, we should not only understand it when choosing this product. In fact, its disadvantages are also to be understood.
Zhejiang Sealand Technology Co., Ltd.is a trustworthy supplier of Oil Mass Flow Meter, Oil Mass Flowmeter, Oil Coriolis Flow Meter, Oil Coriolis Flowmeter, Oil Coriolis Flow Meter, ATEX, IECEx & CE approved.
Operating Environment
Atmospheric pressure: 85kPa~106kPa
Ambient temp.: Refer to Chapter 1.6
Relative humidity: 5%~95%, non condensing
Operating conditions
Fluid: Liquid/Gas
Fluid temperature: -200°C~+200°C (higher temp. model is customizable)
Nominal pressure: 4MPa or 25MPa (Customizable)
Supply voltage: AC 85~265VAC, 50/60Hz or DC 12~24VDC(±5%), 5W
Outputs: Pulse 0~10KHz, RS-485, 4-20mA & HART (optional)
The meter consists of mass flow sensor and transmitter. Mass flow sensor is a phase-sensitive resonant sensor based on Coriolis effect, composed of vibration tube, signal detector, concussion driver, structural support, shell, etc.
Mass flow transmitter is a micro-programming-centered electronic system, which supplies
thrust to sensor, transforms sensor signal into mass flow signal & others, and improves
accuracy in accordance with temperature parameter.
It`s composed of switching power supplier, guard grating, core processor board, display
module, etc., installed in a ex-proof junction box. Switching power supply offers power for
transmitter; safe grating isolates sensor and transmitter intrinsically; core processor detects
& processes sensor phase signal, sends mass flow signal and process communication.
Oil Mass Flow Meter, Oil Mass Flowmeter, Oil Coriolis Flow Meter, Oil Coriolis Flowmeter, Oil Coriolis Flow Meter
Zhejiang Sealand Technology Co., Ltd. , https://www.sealandflowmeters.com