RY thermal oil pump to make the structure simple, small size, saving running costs, good performance, reliable use of self-heating cooling structure, changing the traditional water-cooled structure is China's absorption and digestion of foreign hot oil pump developed based on the second generation of products , Thermal oil pump with packing seal and mechanical seal in the form of combination, packing seal with high temperature filler, has a good thermal adaptability, the product is mainly used for conveying non-solid particles of weakly corrosive high temperature liquid, the use of temperature ≤ 370 ℃, is an ideal hot oil pump. Botou City Jinhai Pump Manufacturing Co., Ltd. is a professional manufacturer of RY heat transfer oil pump, with a sound production system and quality assurance system, product design using advanced international level physical design software; product development Manufacturing, Inspection, Delivery and Service According to the quality control process of GJB9001A military product quality control system, the manufactured heat pump is widely used in petroleum, chemical, rubber, plastics, pharmacy, textile, printing and dyeing, road building and food industries. RY thermal oil pump scope of application: Suitable for conveying weak corrosive liquids without solid particles, suitable temperature -20 ~ +350 ℃, but also According to user needs, flow components use different materials, conveying corrosive liquids or other special properties. For the petrochemical industry, textile printing and dyeing industry, dye industry, wood processing, food industry, plastic and rubber processing industry, paper and printing industries. RY series air-cooled heat pump has a certain pump structure, in the actual production can be assembled in accordance with the structure of the form, in use in accordance with the working principle of work, RY series air-cooled heat pump shaft with a filler box , The sealing performance is more reliable, at the same time in the bearing seat is provided with a mechanical seal, so a large number of leaks can not occur, and a small amount of leakage can drain through the spout to receive. It is normal to have a small amount of leakage early in operation, and the leakage will decrease or stop after the sealing surface has run through a certain period of time. There are two ball bearings in the bearing housing of the heat transfer oil pump. One ball bearing on the pump impeller side of the heat pump is lubricated by the heat transfer oil. One ball bearing on the coupling side is lubricated with high temperature grease. After a ball bearing is operated for 3000 hours, it must be dismantled and cleaned with diesel oil. Check if the contact surface is damaged. If it is damaged, it must be replaced with a new one. Do not use the input pipe gate valve to regulate the flow, to avoid cavitation. RY series of air-cooled heat pump should not be less than 30% of the design flow continuous operation, if you must run under the conditions, it should be installed in the bypass bypass pipe exports, and to flow above the minimum. Multi-gear with three or more than three gears constitute a multi-gear gear pump, driven gear evenly distributed around the driving gear, allowing such gear pump to obtain a variety of displacement, the displacement can either split output , Respectively, to drive different actuators, but also can confluence output large displacement, to achieve the rapid movement of the work organization. The housing of the heat-conducting oil pump or the front and back end caps are provided with corresponding inlet ports and outlet ports respectively, and are respectively connected with the oil suction pipe and the oil discharge pipe. This heat transfer oil pump in addition to access to a variety of output displacement, another significant advantage is that: due to the suction and discharge ports symmetrical layout, and driven gear evenly distributed, so that the hydraulic pressure and meshing force to balance Reduce the pump shaft, bearing load, improve gear pump life. However, the oil pump of the gear pump is more complicated than the conventional two-gear gear pump. In particular, it is difficult to design and process the internal gear of the gear pump with internal gear. These problems are still to be further studied. Pay attention to RY series air-cooled heat pump running without noise, if the pilot state is found, should be promptly processed. Shutdown: cut off the power. The liquid in the hot oil pump will be drained, cleaned, and the impeller should be rotated 180 degrees periodically to prevent the shaft from deforming until the pump is completely cooled. Transmission medium to heat pump oil pump cover and bearing the heat from the pump cover and bearing surface cooling, so that the bearing temperature to adapt to the shaft sealing performance temperature. Therefore, the choice of guided heat pump installation location, to make the pump cover and bearing seat of the heat to facilitate diffusion, does not appear any heat storage. Heat transfer oil pump can produce certain control in the transmission medium, according to a certain technical process control, to ensure that in actual use there is no certain anomalies, to ensure the use of the use of efficiency.
Carbide twist drill 5XD is our standard drill with shorter flute length, widely used for drilling workpiece with shallow holes.
Carbide drill bits with coolant through, mostly used for drilling stainless steel, cause stainless steel is a hard material, a lot of heat generated during the drilling process, coolant-fed can cool down the drill, to extend the tool life.
5Xd Twist Drill,Twist Drill Bit For Metal,Twist Drill Bits,Precision Twist Drill
ROYI CNC TOOL TAIXING CITY CO.,LTD , https://www.royitools.com