1, waterproof construction should use waterproof coating
2. The waterproof project should be done after the concealed project construction is completed and accepted
3, After the completion of waterproof construction to do two water storage test
4, the bathroom waterproof layer should not be less than 1.8 meters
5, floor drain, Yin Yang angle, pipelines and other places to do more waterproof
6, floor drain to use deodorant floor drain
7, hot and cold water left hot right cold
8, try not to walk from the ground
9, cold water pipe in the wall should have a protective layer of 1CM, hot water pipe is 1.5CM, so the slot to open deep
10, PPR pipe is installed to consider the thickness of the tiles, so that the pipe will not be exposed
11, only a few minutes to cook, wash vegetables for a long time, bucket must buy big
12, leading and counter basin to support, can not be installed on the up
13, toilet installation can not use cement, use silicone
14, toilets, taps should be carefully protected after installation
15, to consider the toilet pit when buying a toilet
16, the washing machine to consider whether it is drainage or drainage
17, best not to install the bathroom phone, easy to damp
18, The mirror in the bathroom should first consider the size, otherwise the mirror headlight is very easy to install.
19, bathroom pipe is best to leave the access hole
20, weak electricity can not be worn in the same tube
21, left zero, right phase on the ground 22, the power socket is 300 from the ground, the switch is 1.4 meters 23, the switch is not installed behind the door 24, a lot of sockets should be good 25, high power electrical appliances with 16A sockets, such as electric oven etc. 26, cassette To use a good 27, cassette must be matched with the panel, otherwise it may not be installed on 28, PVC wire and pipe wire cross-section area shall not exceed 40% of the wire tube cross-sectional area
29, bedroom air conditioning not to the bed 30, air conditioning hole to consider outward sloping, otherwise the rain will come in 31, lights try to consider double control 32, the best bathroom to install splash socket 33, balcony to consider a socket 34, wire The trough should be horizontal and vertical, and it should be easy to use afterwards. 35. The public flue should be equipped with a check valve. 36. The purchased appliances must be properly read so that the workers can read the manual 37, the manual and the warranty card. 38. Cement can not be used for more than three months from the delivery date. 39. Cement of different types and numbers must not be mixed. 40. Yellow sand must be used for river sand. Taste and taste for the mouth will tell. 41. Wall tiles should be soaked for more than two hours. After you can post 42, wall tiles will rather buy a few more pieces, do not buy less, or prone to color difference 43, a wall can not have two rows of non-complete bricks 44, wipe the seams immediately after the completion of the tiles to clean 45, the ground paste marble (Light color), the back of the stone should be waterproof 46, 45 degrees angle should be cut at the angle of the corner 47, the floor tile should be inclined to the floor drain, otherwise it is easy to collect water 48, the wall tiles should meet the pipeline mouth to adopt the cut Form, so it looks like a whole piece of brick 49, floor marble should be dry shop 50, floor tiles must be dirty, non-slip, not just to be beautiful 51, matt tiles difficult to clean 52, balcony tiles to pay attention to the drainage direction carpentry 53, to The keel is best to be dried with larch 54. After the large wooden plate is bought, it is to be sawed and air dried. 55. The woodwork enters the arena to play the house's horizontal line 56, and the color panel comes in. Paint brushes will be bought again to prevent it from being contaminated57. Ceiling fans can not be installed on ceiling keels. 58. Color panels should be pre-selected for color construction. 59. Suspended ceilings should not be greater than 300.
60. The gypsum board should be fixed with a countersunk head tapping screw, enter the surface of the board 1~2mm, and do rust treatment, can not use the gun nail 61, the distance between the plasterboard nails shall not be greater than 200
62. The gypsum board should have 3MM seams with the wall for crack prevention. 63. The best protection for the corners of the gypsum board is the protection of the corners. 64. The top and bottom of the door should be painted. 65. The bottom of the bathroom door cover should be brushed. Waterproof 66, the size of the door should be the same 67, furniture, try not to do carpentry, do not do a good 68, try to buy the whole cabinet, carpentry is not good, the design is not OK 69, the size must be considered , It will be more troublesome to change it. 70. Do not do the dark track with the sliding door you do yourself. There will be no way to repair the 71. If the bathroom is small, try to do the sliding door, do not open the door, occupy the place 72, and the woodwork must not be allowed to work with the foreman. More exchanges, do not let them make their own ideas 73, the money in hand is the last word 74, there are children at home, the glass should be less 75, the workers must be good to see the drawings 76, the kitchen drawer is very useful 77, floor wood keel formation Degree is 5MM
78, wool floor to be paved 30 degrees or 45 degrees, between the board and the board to stay 2 ~ 3MM, stitches to be staggered 79, between the floor and the wall to stay 8 ~ 10MM seam 80, when the length of composite flooring over 8M to be considered Expansion joints 81, Minimally use MDF as door covers 82, Hinge and hardware must be used well 83, Yuba to be installed on wooden keels, Can not be directly installed on ceiling painter 84, Medium and dark latex paint construction Do not mix with water as much as possible, otherwise it is prone to color differences. 85. Gypsum board joints should be placed on the bandages 86. There are gaps in the walls where the really cool cloth is better. 87, some of the original wall putty is best to eradicate, or brush it again Glue seal 88, try to buy well-known brands of paint, decoration company recommended or recommended by the foreman try not to use 89, the weather is too wet, the paint does not brush 90, paint, paint, etc. to dry completely after 91, The next paint application must wait for the previous paint to dry out. 92. The metal surface paint should be rust-proof. 93. The weather is too cold. The paint construction quality is poor. 94. When the door paints, use a textured paper to cover the hinge. And door lock 9 5, too hot, pay attention to ventilation 96, when wallpapering, to clean the oil on the wall 97, wallpaper, the switch, socket panel to be removed 98, light, mercerized latex paint to be completed once, make up Easy to appear color difference 99, after the skirting line is installed, use putty and latex paint to make up the seam 100, frosted glass to use the newspaper to protect
Three trees Lacquer paint Lacquer sockets Lacquer-lacquer switch fittings Fittings for decoration companies Glass bricks Drawers Cabinets Doors Ceiling fans Lamps Marble tile Mirrors Front lamps Glass sliding doors Glass furniture Marble Cabinets Kitchen wall tiles Doors Floorings Kitchen cabinet doors Glass doors Kitchen glass Sliding door bathroom tile bathroom door bathroom wall tile bathroom door size bathroom size bathroom ceiling overall bathroom bathroom design bathroom waterproof bathroom floor tile bathroom sliding door tile adhesive kitchen tile balcony tile small bedroom floor tile bedroom lamp
Due to its wide range of uses, there are also many varieties of hook and loop sanding disc. The most commonly used are red sanding disc, yellow/gold sanding disc, green sanding disc, and white sanding disc, etc.
The sandpaper disc is using aluminum oxid abrasives, with grits as below: 40#, 60#, 80#, 120#, 180#, 240#, 320#, 400#, 600#, 800#, 1000#, 1200#, 1500#, 2000#.
The abrasive polishing disc can be punched into various shapes, round, round with holes, triangle, rectangle, iron shape, neckline shape, etc.
This product is round abrasive disc size: 100mm, 125mm, 150mm, 180mm, 225mm or other size can be customized.
The holes best selling is with 6 hole, 8 holes, 15 holes, 17 holes or customized.
The main purpose of our abrasive sanding disc:
1. Polishing of primer and finishing of paint, such as mid-coat paint/primer grinding of ships.
2. Polishing of synthetic materials, such as burr sharp edges and surface adjustment after plastic products are formed.
3. Grinding of metal and aluminum alloy to remove foreign matter and surface particles.
4. Suitable for making various specifications of brushed and self-adhesive sand discs.
This abrasive sanding disc is one of our main abrasive products, as the manufacture of abrasive tools, we mainly produce the Flap Disc Backing Pad, Flap Disc Adhesive, Abrasive Flap Disc, Bonded Abrasives ( Cutting Wheels and Grinding Wheels ), Abrasive Machine , etc. So welcome more orders, we can offer you best quality product with best competitive price, please contact Emma.
Abrasive Sanding Disc,Sanding Disc,Metal Sanding Disc,Abrasive Tools Sanding Disc
Zhengzhou Jiading Abrasive Manufacturing Co.,Ltd , https://www.abrasive-jd.com