As we all know, the kitchen is the most provoked place. Everyone will install a range hood at home, so when cooking, it will not be snuffed. The flue has also become an indispensable decoration device in large-scale kitchen equipment. Its function is to discharge fumes through the flue. So what is the installation method of soot piping ? What should you pay attention to when installing? Let's take a look at the installation of smoke pipes.
Smoke Pipe Introduction
The fume pipe is an important channel for the family to eliminate fumes, which are generally divided into indoor fume pipes and outdoor fume pipes. The indoor fume pipes are relatively thin and are generally installed on the hood of the hood to better exclude soot. Outdoor smoke pipes are the main route for multiple households to exclude fumes, and their pipes are relatively large. Generally, there are white iron (galvanized steel) exhaust pipes and black steel (iron) exhaust pipes. Smoke pipes are widely used in construction projects such as restaurants, hotels, hotels, hospitals, factories, mall buildings, and office buildings.
Smoke pipe installation method
First, the vice flue must be kept
Each home has a flue in the kitchen, and the flue also has the main and auxiliary points. The main flue duct runs through the entire building, while the auxiliary flue is relatively independent. In general, the fumes in the home will go to the auxiliary flue and then enter the main flue through the holes in the partition. This will ensure that the fumes of each household are isolated. However, if the secondary flue duct is directly connected to the main flue duct, the phenomenon of smoking or crosstalk may occur due to the low pressure.
Second, construction details should pay attention
First of all, it is very important to choose the location where the range hood is installed. The shorter the pipeline, the better. Some owners will pull the pipeline long for beauty, so that after the hood is turned off, there will be a lot of soot accumulated in the pipeline, and it will be returned to the interior. In addition, in order not to destroy the original main and auxiliary flue, its opening direction is not arbitrarily changeable, and must be played inside the auxiliary flue.
Third, the window to pay attention to safety
First of all, before the window or wall hole must be agreed by the property; followed by attention to safety issues, the general end of the exhaust pipe metal material, if the hole is too small, the metal heat transfer may cause the glass burst, hurting pedestrians And the smoke pipe leads out of the window. The strong north wind blowing against the air will cause the fumes to fall. It is better to stick the pipe out and put the pipe down into the nest. This will also prevent the rain from flowing into the pipe when it rains and keep the wind out.
Fourth, stop valve replacement
If you have dismantled the secondary flue, or if you need to prevent better smoking, use a flue check valve. Under normal circumstances, the effect of the non-return valve of the hood is not obvious, and installing the non-return valve in the flue can protect the hood, so that the smoke in the flue will not be poured into the pipeline and the hood. However, after installing the non-return valve, it should be cleaned regularly. Otherwise, the non-return valve will be opened and lose its effect. Moreover, the flue check valve should be replaced once every two years.
Smoke pipe installation considerations
The most important part of the installation of the smoke pipe is the seal of the pipe interface and the special fire protection card. The installation of the soot pipe is done by professional decoration personnel. If consumers do not know how to do it, do not use it alone. Installation, to avoid unsightly installation and cause unnecessary trouble.
1. First of all, we need to check whether there is a space reserved for the upper part of the fume pipe and the condition of the space reserved.
2. Pay attention to the gap of the flue mouth when the flue gas exhaust pipe is embedded and ensure that it does not fall off.
3, before the ceiling smoke exhaust pipe pre-embedded into the ceiling, the need to determine the location of the exhaust pipe on the ceiling exposed mouth according to the design drawings of the cabinet, need to refer to the style of the hood, generally speaking European-style hood The pipe is in the middle position, while the exhaust nozzle of the baronet is on the side of the hood. These conditions affect the location of the reservation.
4. If the cooker is placed on the side of the Yintai, you need to pay attention to whether the fume pipe passes through the lintel of the building. In principle, the general property management department is not allowed to cross the smoke exhaust pipe through the lintel. This treatment method can not only not consider the distance between the smoke pipe mouth and the wall, to avoid the smoke pipe mouth distance from the wall is greater than the depth of the wall cabinet and affect the installation of the hanging cabinet, but also can avoid the completion of the installation after the cabinet There is a horizontal smoke exhaust pipe at the top which affects the appearance.
5, this way will inevitably be exposed on the ceiling and the upper part of the hood to walk up and down the pipe, we can be based on the position and height of the smoke pipe design envelope board to be modified.
Summary: About fume pipe installation method for everyone to introduce here, I hope the efforts of Xiao Bian can help you, if you do not understand what you can do to the bottom of the Xiaobian message, we will answer as soon as possible, This website will provide you with more complete, more detailed and updated information.
Construction Installation Curtain Installation Method Pipeline Heating Installation Pipe Leakage
Diamond Micro-powder is a new type of super hard and super fine abrasive.It is produced by High Pressure Diamond Micro-powder
Feature:
--the same crystal form
--pure color
--high purity
--good impact resistance
--wear resistance
Application:
For diamond abrasive polishing, Grinding Wheel production.
Diamond Micro-Powder,Synthetic Diamond Monocrystal,High-Pressure Micro Powder Mill,Diamond Micron Powder For Natural Diamond
Henan Bohong New Material Co., Ltd , https://www.bohongpcd.com