Order: first put wall tiles, then paste tiles.
Time: A good bricklayer sticks 5-6 squares a day, otherwise it is difficult to guarantee quality. Especially in the case of windowsills where small diagonals are needed, it is time consuming.
Material selection:
1, polished tiles: the surface is smooth and bright.
2. Vitrified tiles: The surface is smooth and bright, but it is denser than the polished tiles and does not seep through.
3, mosaic: The current mosaic variety and technology gradually increase, high-quality glass mosaic is expensive, in 300 yuan / square meter or more, can be used to decorate.
4, marble: the general family with caution, it is best to use when the role of local embellishment.
5, sealant: Now the average family tile, has not used the white cement groove joints. Colourful caulking agent can sometimes bring unexpected effects to ordinary tiles.
Construction sequence:
The basic process of paving ceramic floor tiles 1. Paste colored glazed tiles:
Treat grassroots → bullets → tile soaking wet → spread cement mortar → install standard block → paving bricks → sew → clean → curing.
2, paving ceramic mosaic tiles (mosaic) categories:
Deal with grassroots → elastic line, marking bar → paving cement mortar → paving → tapping → sprinkling, peeling paper → picking, filling, cleaning → cleaning.
Paving ceramic tile construction points 1, the concrete floor should be the base cut hair, cutting hair depth of 5 to 10 mm, the distance between the cutting hair marks is about 30 mm. After that, clean the floating ash, mortar, and oil stains, and produce scattered water to sweep the ground.
2. Before the paving, a good line should be played. On the ground, a reference line at right angles to the doorway opening should be popped. The line should be started from the entrance to ensure that the entrance is a whole brick, and the non-complete brick is placed under the overcast or furniture. The vertical and horizontal positioning control lines appear.
3, before laying ceramic tiles, ceramic tiles should be soaked in the shade.
4. When laying, cement mortar should be fully applied on the back of the ceramic floor tile. At the same time, use a level ruler to check and correct and wipe the surface cement mortar.
5. After 2 to 3 hours of paving, use white cement to wipe the joints. Use cement mortar and sand=1:1 (volume ratio) cement mortar. The joints should be densely packed and smooth. Wipe the surface with cotton again.
6, attention.
(1) The grassroots must be qualified for treatment, and there must be no floating soil or floating dust.
(2) Ceramic tiles must be soaked and dried. After free from affecting the coagulation and hardening, hollowing, shelling and other problems occur.
(3) No person will be allowed within 2~3 hours after completion of paving. Ceramic tile should be maintained 4~5 days before
Time: A good bricklayer sticks 5-6 squares a day, otherwise it is difficult to guarantee quality. Especially in the case of windowsills where small diagonals are needed, it is time consuming.
Material selection:
1, polished tiles: the surface is smooth and bright.
2. Vitrified tiles: The surface is smooth and bright, but it is denser than the polished tiles and does not seep through.
3, mosaic: The current mosaic variety and technology gradually increase, high-quality glass mosaic is expensive, in 300 yuan / square meter or more, can be used to decorate.
4, marble: the general family with caution, it is best to use when the role of local embellishment.
5, sealant: Now the average family tile, has not used the white cement groove joints. Colourful caulking agent can sometimes bring unexpected effects to ordinary tiles.
Construction sequence:
The basic process of paving ceramic floor tiles 1. Paste colored glazed tiles:
Treat grassroots → bullets → tile soaking wet → spread cement mortar → install standard block → paving bricks → sew → clean → curing.
2, paving ceramic mosaic tiles (mosaic) categories:
Deal with grassroots → elastic line, marking bar → paving cement mortar → paving → tapping → sprinkling, peeling paper → picking, filling, cleaning → cleaning.
Paving ceramic tile construction points 1, the concrete floor should be the base cut hair, cutting hair depth of 5 to 10 mm, the distance between the cutting hair marks is about 30 mm. After that, clean the floating ash, mortar, and oil stains, and produce scattered water to sweep the ground.
2. Before the paving, a good line should be played. On the ground, a reference line at right angles to the doorway opening should be popped. The line should be started from the entrance to ensure that the entrance is a whole brick, and the non-complete brick is placed under the overcast or furniture. The vertical and horizontal positioning control lines appear.
3, before laying ceramic tiles, ceramic tiles should be soaked in the shade.
4. When laying, cement mortar should be fully applied on the back of the ceramic floor tile. At the same time, use a level ruler to check and correct and wipe the surface cement mortar.
5. After 2 to 3 hours of paving, use white cement to wipe the joints. Use cement mortar and sand=1:1 (volume ratio) cement mortar. The joints should be densely packed and smooth. Wipe the surface with cotton again.
6, attention.
(1) The grassroots must be qualified for treatment, and there must be no floating soil or floating dust.
(2) Ceramic tiles must be soaked and dried. After free from affecting the coagulation and hardening, hollowing, shelling and other problems occur.
(3) No person will be allowed within 2~3 hours after completion of paving. Ceramic tile should be maintained 4~5 days before
Construction acceptance cement glass door price window furniture glass brick marble tile floor brick craft glass glass furniture glass door tile price
Various designs-round shape, square shape.
Different sizes: round-38mm, 48mm, 58mm
Product categories of Common Toilet Seat, we are specialized manufacturers from China, Common Toilet Seat, Toilet Seat Cover suppliers/factory, wholesale high-quality products of Toilet Lid R & D and manufacturing, we have the perfect after-sales service and technical support. Look forward to your cooperation!
dual flush button, dual push button, push button for toilet, toilet button
XIAMEN JIEENTE IMPORT AND EXPORT CO.,LTD , https://www.jieentexm.com