Introduction: In the "Thoughts on the Series Design of Photovoltaic Modules (1)", the author shared the traditional way of designing photovoltaic string strings. However, some calculation errors tend to occur in traditional designs. Today, the author will analyze these errors and propose relevant improvement ideas.
In traditional designs, calculation errors occur.
1, the error caused by the temperature value
Since extreme cold temperatures are the lowest values ​​of ambient temperature throughout the day, the component temperatures during operation should be higher than this value. Therefore, the N1 result above will be low.
Assuming that the minimum ambient temperature is -30°C throughout the day, it certainly appears during non-operating nights; if the extreme low temperature during daytime operation is above -18°C, N1≤23 is calculated and 23 strings can be used for each string. The program.
Therefore, if you use the extreme cold temperatures for the daytime, the number of strings in each string may increase.
2, the value of open circuit voltage
In the calculation of "Example 1", Voc is taken as the open circuit voltage at the nominal power, that is, the open circuit voltage at 260 W. At this time, the irradiance is 1000 W/m2.
However, when the irradiance = 1000W/m2, it must be around noon, and certainly no extreme low temperature. From the IU curve in Fig. 2, it can be seen that when the irradiance decreases, the open circuit voltage changes slightly but still decreases slightly.
Figure 2 IU curve of photovoltaic modules
The component parameters in Table 1 are divided into STC conditions and NOCT conditions. Under the condition of NOCT, if the irradiance is 800W/m2, although extreme low temperature will certainly not occur at this time, relative to the irradiance=1000W/m2, the parameter values ​​are relatively more accurate. According to Table 1, when using the post-correction method to perform the string design of "Example 1", the values ​​of each quantity are as follows:
Table 3 Corrected Voltage Values
The results are shown in the table below.
It can be seen that when the other conditions are exactly the same, the correction method is used to calculate. The calculation result of "Example 1" is: open circuit voltage: N1 ≤ 24; MPPT voltage: 17 ≤ N2 ≤ 25, and the final series number is taken as 24.
Of course, if the irradiance is 800W/m2, the possibility of extreme low temperatures is also relatively small. If the irradiance = 200W/m2 component parameters, the calculation results should be more accurate; but after correction, the 260W components In the case of extremely low temperature ≥ -30°C, it is feasible to use 24 components per string.
We carry high quality Speed Governor as below
Passenger Elevator Speed Governors, Panoramic Elevator Speed Governors, Home Elevator Speed Governors, Hospital Bed Elevator Speed Governors, Freight Elevator Speed Governors, Car Elevator Speed Governors, Service Elevator Speed Governors, Goods Elevator Speed Governors, MRL Elevator Speed Governors
for all major elevator and escalator brands as below
OTIS Elevators, ThyssenKrupp Elevators, Schindler Elevators, KONE Elevators, Mitsubishi Elevators, Fujitec Elevators, Hitachi Elevators, Toshiba Elevators, Fuji Elevators, Express Elevators, Sigma Elevators, LG Elevators, Hyundai Elevators, BLT Elevators, CANNY Elevators, SJEC Elevators, KOYO Elevators, IFE Elevators, Thyssen Elevators, GiantKONE Elevators, XJ Schindler Elevators, Xizi OTIS Elevators, Shanghai Mitsubishi Elevators, GUANGRI Elevators
OTIS Elevator Overspeed Governor, Thyssen Elevator Overspeed Governor, KONE Elevator Overspeed Governor, GiantKONE Elevator Overspeed Governor, ThyssenKrupp Elevator Overspeed Governor, Schindler Elevator Overspeed Governor, XJ Schindler Elevator Overspeed Governor, Xizi OTIS Elevator Overspeed Governor, Mitsubishi Elevator Overspeed Governor, Shanghai Mitsubishi Elevator Overspeed Governor, Fujitec Elevator Overspeed Governor, Hitachi Elevator Overspeed Governor, Toshiba Elevator Overspeed Governor, Hyundai Elevator Overspeed Governor, LG Elevator Overspeed Governor, Sigma Elevator Overspeed Governor, Express Elevator Overspeed Governor, GUANGRI Elevator Overspeed Governor, FUJI Elevator Overspeed Governor, BLT Elevator Overspeed Governor, CANNY Elevator Overspeed Governor, SJEC Elevator Overspeed Governor, KOYO Elevator Overspeed Governor, IFE Elevator Overspeed Governor
We also offer multinational corporation with different overspeed governor as below trip speed governor, bail type governor, horizontal shaft governor, pull through governor, centrifugal governor, centrifugal type governor, flyball governor, tail rope governor, displacement governor, displacement type governor, governor safety fence, governor overspeed switch, governor tripping speed, governor catch, governor bracket,
governor rope grip jaw, governor switch, governor rope, governor cable, rope retaining guard, governor sheave, governor rope tension sheave, governor tension sheave, governor rope releasing carrier, governor tension weights, wedge type governor, disk type speed governor, escalator overspeed governor, Elevator Speed Governor, Elevator Overspeed Governor, Elevator Governor
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Elevator Speed Governor,Elevator Overspeed Governor,Over Speed Control Governor,Passenger Elevator Overspeed Governor, Elevator Governors
CEP Elevator Products ( China ) Co., Ltd. , https://www.zjfullelevatorreplacement.com